Royal Oil Co. - Since 1926

REXROC CURING AGENT – Application & Surface Preparation

APPLICATION: SURFACE PREPARATION: Clean surface for repair, removing loose debris, disintegrated concrete, oil, grease and dirt. Flush the area thoroughly REXROC is a one component cement that sets up ready for traffic in less than one hour. Almost three times stronger than concrete, it can be used to repair all types of concrete structures: steps, walkways, fence posts, loading docks, and many other areas. Loading Docks Concrete Steps Concrete Chuck Holes Parking Decks Installation of Bolts in Concrete Floors Bridge Railings Concrete Curbs Freezer Rooms Fence Posts Metal Railings with clean water and allow to dry. A dry surface ensures a better bond. MIXING: At room temperature, the mixing and pouring procedure should take no longer than 10 minutes as…

Read More

Magnemyte – Directions for Use

After thoroughly mixing with water, pour the material into the hole to be repaired and level the patch with the surrounding concrete. Use a mortar-type mixer for large jobs. For smaller jobs, an electric drill with an attachment or a simple shovel is adequate.

Read More

Coverage Rates for: FIBERED ALUMINUM ROOF COATING

Minimum Coverage The following coverage rates are minimums only. If asphaltic roofs are dried out, apply a coating of ROOF PRIMER before the application of FIBERED A.R.C. . Metal Roofs Flat 1 gal. to 100 sq. ft. Corrugated 1½ gal. to 100 sq. ft. Asphalt Coated Roofs 1½ gal. to 100 sq. ft. Roll Roofing Paper 1½ gal. to 100 sq. ft. Masonry Surfaces 1½ to 2 gal. to 100 sq. ft. Modified Bitumen Membrane 1½ gal. to 100 sq. ft. Lumber Dry Kilns 1½ to 2 gal. to 100 sq. ft.

Read More

DRI-MOLY Directions for Use

Shake well before using. Clean surface thoroughly. Hold can 6 to 8 inches from surface and apply even, thin coats. Allow 1 to 5 minutes for adequate drying. The concentration of solids in this product may clog nozzle. Shake vigorously and often. Before storing, turn can upside down and spray until nozzle is clear.

Read More

Aerosol Open Gear & Chain EF How to Use

DIRECTIONS FOR USE Shake well before using. Remove protective cap. Hold can 6 to 8 inches from surfaces to be sprayed. Apply an even coat to surface. Turn on machinery and allow lubricant to spread over all working surfaces. Apply a second thinner coating to insure adequate lubrication. Reapply as needed to lubricate and protect equipment. After spraying turn can upside down and spray until nozzle is clear.

Read More

Royal Fleet Kleen Directions For Use

DIRECTIONS FOR USE: When used through high pressure equipment with direct chemical injections, FLEET KLEEN can be metered directly from its container at a ratio of 1:50 for most applications when the water hardness is moderate to high. In sort water, dilutions as great as 1:150 give complete soil removal. When used in equipment with a chemical concentrate tank, mix one gallon of this product to every five gallons of water. This mixture is then metered at a ratio between 1:10 and 1:30, depending on water conditions and the cleaning requirements of the customer. For manual washing, 3-6 ounces per gallon proves effective for medium to heavy soil loads.

Read More

How to royal clean hand cleaner

Dip, pump or scoop a small amount from the 4½ lb. container or squeeze a small amount from 15 oz. tube and place in palm of your hand. Rub hands together vigorously. This rubbing action causes ROYAL CLEAN to liquefy. After hands are clean, wipe hands with towel until dry or rinse with water and dry hands.

Read More

Green Fury How To

Use 1 to 3 ounces of GREEN FURY to one gallon cold or warm water, depending on soil. Apply solution to pre-rinsed equipment – allow to set approximately 5 minutes. Swab heavily soiled areas with brush, then rinse clean. Safe for car and truck finishes; fast, inexpensive cleaner that rinses free. For inexpensive – only pennies per gallon – yet effective cleaning, use one ounce GREEN FURY to one gallon of cold or hot water. Does not stain or leave dulling soap scum. For a powerful combination of wetting, penetrating and emulsifying action, thoroughly mix one part GREEN FURY with one part kerosene type solvent, then add an additional 4 parts of the kerosene type solvent. After applying, soaking and scrubbing where necessary, surface is quickly rinsed clean…

Read More